Gacq en 02:21 4 dic 2006

2006-12-04T02:21:25Z

192.168.0.105 en 20:44 27 jul 2006

2006-07-27T20:44:36Z

Página nueva

* [http://linuxprinting.org/ LinuxPrinting.org]

= Epson =
== Utilitarios ==
=== escputil ===
Permite ver nivel de tinta, alinear y limpiar cabezales

Para ver el nivel de tinta en los cartuchos
<pre><nowiki>
escputil -r /dev/usb/lp0 -i
</nowiki></pre>

Para ver el estado de la impresora
<pre><nowiki>
escputil -r /dev/usb/lp0 -s
</nowiki></pre>

http://www.biostat.wustl.edu/cgi-bin/info2html?(gimpprint.info.gz)ESC%2FP2%2520Remote%2520Mode%2520Commands
<pre><nowiki>
The actual reply is documented as

@BDC ST\r
ST: xx;
[ER: yy;]
IQ: n1n2n3n4;
[WR: w1,w2...;]
RV: zz;
AI:CW:02kkccmmyy, MI:mm
[TC:tttt;]
INK:...;
\f

(`\r' is carriage return; `\n' is newline; `\f' is formfeed.)

`ST' is the printer status:
`00' Error
`01' Self-test
`02' Busy
`03' Waiting while printing
`04' Idle
`07' Cleaning/filling ink heads
`08' Not yet initialized/filling heads

`ER', if provided, is the error status:
`00' Fatal error
`01' Interface not selected
`04' Paper jam
`05' Out of ink
`06' Paper out

`IQ' is the amount of ink left, as a (decimal!) percentage
expressed in hexadecimal. The values are black, cyan, magenta, and
yellow (presumably 6-color printers supply light cyan and light
magenta inks as additional parameters).

`WR', if provided, is the warning status:

`10' Black ink low
`11' Cyan
`12' Magenta
`13' Yellow
`14' Light cyan (presumably)
`15' Light magenta (presumably)

`RV' is the firmware revision (one byte ASCII).

`AI' is actuator information. These are two byte ASCII codes that
indicate "ink weight rank ID" of KCMY, respectively.

`TC', if provided, is the total time of cleaning or ink filling
(?).

`INK:' and `MI' are *not documented*.
</nowiki></pre>

Monitoreo desde el munin (escputil debe tener suid)
<pre><nowiki>
#!/bin/sh
#
#

#%# family=contrib
#%# capabilities=autoconf suggest

escputil=/usr/bin/escputil

if [ "$1" = "autoconf" ]; then
if $mbmon -c 1 > /dev/null 2>/dev/null ; then
printf "yes\n"
exit 0
else
if [ $?=127 ] ;then
echo "no (executable not found)"
else
echo "no (escputil could not read sensor values)"
fi
exit 1
fi
exit 0
fi

if [ "$1" = "config" ]; then
echo 'graph_title Printer Ink Level'
echo 'graph_order Negro Cian Magenta Amarillo'
echo 'graph_category sensors'
echo 'graph_vlabel C'
echo 'graph_scale no'
echo 'Negro.label Negro'
echo 'Cian.label Cian'
echo 'Magenta.label Magenta'
echo 'Amarillo.label Amarillo'
exit 0
fi

$escputil -r /dev/usb/lp0 -i | tail -4 | sed -e "s/ * //" | sed -e "s/ * /.value /"
</nowiki></pre>
=== mtink ===
Bastante precario

== EPSON Stylus Color 480 - C480 ==

La impresora no imprime con los siguientes errores:

*CUPS Web GUI -> Parallel port busy; will retry in 30 seconds...
*At boot -> lp0 on fire

En mi caso este problema sucedio por que la impresora no tenia tinta en el cartucho color, aparentemente en este caso la impresora envia un codigo de error que no es entendido por el controlador de puerto paralelo y hace que deje de funcionar. El problema se resolvio al instalar un nuevo cartucho color.

= HP =
== HP Deskjet 540C ==

No intentar hacerla andar con el cable paralelo, solo funciona con el USB

← Revisión anterior		Revisión del 02:21 4 dic 2006
Línea 1:		Línea 1:
−	* [http://linuxprinting.org/ LinuxPrinting.org]	+	=Información=
		+	*[http://linuxprinting.org/ LinuxPrinting.org]

	= Epson =		= Epson =

Impresoras - Historial de revisiones

Gacq en 02:21 4 dic 2006

192.168.0.105 en 20:44 27 jul 2006